57 10.2 Foliation and Rock Cleavage

How Foliation Develops

When a rock is acted upon by pressure that is not the same in all directions, or by shear stress (forces acting to “smear” the rock), minerals can become elongated in the direction perpendicular to the main stress. The pattern of aligned crystals that results is called foliation.

Foliation can develop in a number of ways. Minerals can deform when they are squeezed (Figure 10.6), becoming narrower in one direction and longer in another.

Figure 10.6 Foliation that develops when minerals are squeezed and deform by lengthening in the direction perpendicular to the greatest stress (indicated by black arrows). Left- before squeezing. Right- after squeezing. Source: Steven Earle (2015) CC BY 4.0 view source

If a rock is both heated and squeezed during metamorphism, and the temperature change is enough for new minerals to form from existing ones, the new minerals can be forced to grow longer perpendicular to the direction of squeezing (Figure 10.7). If the original rock had bedding (represented by diagonal lines in Figure 10.7, right), foliation may obscure the bedding.

Figure 10.7 Effects of squeezing and aligned mineral growth during metamorphism. Left: Protolith with diagonal bedding. Right: Metamorphic rock derived from the protolith. Elongated mica crystals grew perpendicular to the main stress direction. The original bedding is obscured. Source: Steven Earle (2015) CC BY 4.0 view source

This is not always the case, however. The large boulder in Figure 10.8 in has strong foliation, oriented nearly horizontally in this view, but it also has bedding still visible as dark and light bands sloping steeply down to the right.

Figure 10.8 A geologists sits on a rock that has foliation (marked by the dashed line that is nearly horizontal), and still retains evidence of the original bedding (steeply dipping dashed line). The rock has undergone a relatively low degree of metamorphism, which is why the bedding is still visible. Source: Karla Panchuk (2018) CC BY 4.0, modified after Steven Earle (2015) CC BY 4.0 view source

Foliation and Crystal Habit

Most foliation develops when new minerals are forced to grow perpendicular to the direction of greatest stress. This effect is especially strong if the new minerals grow in platy or elongated shapes. The rock in the upper left of Figure 10.9 is foliated, and the microscopic structure of the same type of foliated rock is shown in the photograph beneath it. Over all, the photomicrograph shows that the rock is dominated by elongated crystals aligned in bands running from the upper left to the lower right. The stress that produced this pattern was greatest in the direction indicated by the black arrows, at a right angle to the orientation of the minerals. The aligned minerals are mostly mica, which has a platy crystal habit, with plates stacked together like pages in a book.

Figure 10.9 A foliated metamorphic rock called phyllite (upper left). The satin sheen comes from the alignment of minerals. Lower left- a view of the same kind of rock under a microscope showing mica crystals (colourful under polarized light) aligned in bands. The region outlined in a red dashed line shows a lens of quartz crystals that do not display alignment. Upper right- stacks of platy mica crystals. Lower right- a blocky quartz crystal. Source: Karla Panchuk (2018) CC BY-SA 4.0. Click the image for photo sources.

The zone in the photomicrograph outlined with the red dashed line is different from the rest of the rock. Not only is the mineral composition different—it is quartz, not mica—but the crystals are not aligned. The quartz crystals were subjected to the same stress as the mica crystals, but because quartz grows in blocky shapes rather than elongated ones, the crystals could not be aligned in any one direction.

Even though the quartz crystals themselves are not aligned, the mass of quartz crystals forms a lens that does follow the general trend of alignment within the rock. This happens because the stress can cause some parts of the quartz crystals to dissolve, and the resulting ions flow away at right angles to the greatest stress before forming crystals again.

The effects of recrystallization in Figure 10.9 would not be visible with the unaided eye, but when larger crystals or large clasts are involved, the effects can be visible as “shadows” or “wings” around crystals and clasts. The rock in Figure 10.10 had a quartz-rich conglomerate as a parent rock. Differential stress has caused quartz pebbles within the rock to become elongated, and it has also caused wings to form around some of the pebbles (see the pebble in the dashed ellipse). The location of the wings depends on the distribution of stress on the rock (Figure 10.10, upper right).

Figure 10.10 Metaconglomerate with elongated of quartz pebbles. The pebbles have developed “wings” to varying degrees (e.g., white dashed ellipse). These are the result of quartz dissolving where stress is applied, and flowing away from the direction of maximum stress before recrystallizing (upper right sketch). Source: Karla Panchuk (2018) CC BY-NC-SA 4.0. Photo by R. Weller/ Cochise College view source. Click the image to view terms of use.

Foliation Controls How Rocks Break

Foliated metamorphic rocks have elongated crystals that are oriented in a preferred direction. This forms planes of weakness, and when these rocks break, they tend to break along surfaces that parallel the orientation of the aligned minerals (Figure 10.11). Breaks along planes of weakness within a rock that are caused by foliation are referred to as rock cleavage, or just cleavage.  This is distinct from cleavage in minerals because mineral cleavage happens between atoms within a mineral, but rock cleavage happens between minerals.

Figure 10.11 Close-up view of a metamorphic rock with aligned elongated crystals. The crystals control the shape of the break in the rock (black gap), resulting in breaks occurring along parallel surfaces. Source: Karla Panchuk (2018) CC BY 4.0

The mineral alignment in the metamorphic rock called slate is what causes it to break into flat pieces (Figure 10.12, left), and is why slate has been used as a roofing material (Figure 10.12, right). The tendency of slate to break into flat pieces is called slaty cleavage.

Figure 10.12 Rock cleavage in the fine-grained metamorphic rock called slate results in breaks along relatively flat surfaces (left). This is why slate has been used for roofing material (right). Source: Left- Roger Kidd (2008) CC BY-SA 2.0 view source; Right- Michael C. Rygel (2007) CC BY-SA 3.0 view source

Rock cleavage is what caused the boulder in Figure 10.8 to split from bedrock in a way that left the flat upper surface upon which the geologist is sitting.